Difference between revisions of "Creality Ender 5 Pro"
Jump to navigation
Jump to search
Line 1: | Line 1: | ||
==Filament Info== | |||
The Ender 5 Pro printers use 1.75mm Filament | |||
==Octoprint Information== | ==Octoprint Information== | ||
;Octoprint Web Page Ender 5 Pro 1 | ;Octoprint Web Page Ender 5 Pro 1 |
Revision as of 17:54, 6 August 2021
Filament Info
The Ender 5 Pro printers use 1.75mm Filament
Octoprint Information
- Octoprint Web Page Ender 5 Pro 1
- http://hh-octopi-2.local/
- IP Address
- xxx.xxx.xxx.128
- Controller board version
- V4.2.2
- Firmware version
- 1.3.1 2020/04/25
- Firmware Family
- Marlin
- Issues
- This version sends duff temperature data. It duplicates every value. A special plugin is identified by Octoprint and needs to be installed for Octoprint to correctly display temperature values.
- This version does not save key parameters when powered off even after clicking STORE in two different places.
- On Power on set Extruder steps/per mm to = 96.5
- On Power on set Z axis offset to = -1.80mm
- Googling reveals for this board and firmware the MicroSD card MUST be in the SDCard slot at power on and power off or the settings are lost!
- Octoprint Web Page Ender 5 Pro 2
- http://hh-octopi-3.local/
- IP Address
- xxx.xxx.xxx.130
- Controller board version
- V1.1.5
- Firmware version
- Firmware Family
- Marlin
- Issues
- Non currently
- Suggested Tool Flow
-
- Obtain STL or OBJ model from thingiverse or craft one in modelling software.
- Configure print settings and slice using Slic3r.
- Upload directly from Slic3r to Octoprint.
- Start and monitor print from Octoprint web interface.
- Cancel Print if needed or adjust temperatures on the fly.
- Admire freshly 3d printed object.
Manufacturer
- Manufacturer Website: https://www.creality.com/
- https://www.creality.com/download
Manual
Bed Levelling Guide
- Local Copy of Bed Levelling Guide: Automatic Leveling(1284Pmainboard)instruction(英文)V.1.3.pdf
Use this Manual if you ever need to reset the nozzle offset.
Slicer G-Code Customisation
NOTE: As the Ender 5 Pro has a built in BLTouch bed levelling sensor you MUST change the machine settings in your Slicer so that the Start G-Code entry from:
G28 ; Original Home command
to
G28 ; Original Home command G29 ; Home Command that uses BLTouch Bed Levelling
Assembly Manual
Use the Bed Levelling Guide above ^^^^^^^^ not the guide in this manual as it is for the Ender 5 without the BLTouch.
- Local Copy of Printer Manual: Ender 5 Pro User Guide and Assembly Manual
Printer Data
- Downloadable Source data for printer:
- Additional Octoprint Info
Octoprint Printer Profile Data
- General
- Name = No 1 Ender 5 Pro (No 2 Ender 5 Pro)
- Identifier = no_1_ender_5_pro (no_2_ender_5_pro)
- Model = No 1 Ender 5 Pro (No 2 Ender 5 Pro)
- Printer Bed & Build Volume
- Form Factor = Rectangular
- Origin = Lower Left
- Heated Bed = Check
- Heated Chamber = Un-checked
- Print Volume
- Bed Width (X) = 220mm
- Bed Depth (Y) = 220mm
- Height (Z) = 300mm
- Custom bounding box = Un-checked
- Axes
- Define the maximum speed/feedrate of the individual axes.
- X = 600 mm/min
- Y = 600 mm/min
- Z = 200 mm/min
- E = 300 mm/min
- Hotend & Extruder
- Nozzle Diameter = 0.40 mm
- Number of Extruders = 1
Firmware
- Creality
- Main Board Hardware Version
- https://www.creality.com/download