Difference between revisions of "Lulzbot Taz 4"
(24 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
==Filament Info== | |||
The Lulzbot Taz 4 printer uses 2.85-3.00mm Filament | |||
==Octoprint Information== | ==Octoprint Information== | ||
;Octoprint Web Page | ;Octoprint Web Page | ||
:http://hh-octopi- | :http://hh-octopi-1.local/ | ||
;IP Address | ;IP Address | ||
: | :xxx.xxx.xxx.128 | ||
;Suggested Tool Flow : | ;Suggested Tool Flow | ||
:# Obtain STL or OBJ model from thingiverse or craft one in modelling software | : | ||
:# Obtain STL or OBJ model from thingiverse or craft one in modelling software. | |||
:# Configure print settings and slice using Slic3r. | :# Configure print settings and slice using Slic3r. | ||
:# Upload directly from Slic3r to Octoprint. | :# Upload directly from Slic3r to Octoprint. | ||
Line 13: | Line 17: | ||
==Manufacturer== | ==Manufacturer== | ||
*Manufacturer Website: https://www.lulzbot.com/ | * Manufacturer Website: https://www.lulzbot.com/ | ||
===Compatible Slicer=== | |||
According to the Lulzbot forums (https://forum.lulzbot.com/t/taz-4-settings/5486/4) the last Cura version Lulzbot had that supported the TAZ4 is 21.08 here http://download.lulzbot.com/Software/Cura/Packages/Cura_21.08/ | |||
Configure Cura 21.08 at start up with | |||
* Select Your Machine = Lulzbot TAZ 4 or 5 | |||
* Lulzbot TAZ 4-5 Selection = Stock TAZ 4 (PET & v1) | |||
==Manual== | ==Manual== | ||
*Printer Manual: https://download.lulzbot.com/KITTAZ/documentation/manual/Manual.pdf | * Printer Manual: https://download.lulzbot.com/KITTAZ/documentation/manual/Manual.pdf | ||
*Local Copy of Printer Manual: | * Local Copy of Printer Manual:[[Media:TAZ_Lulbotz_4_Manual.pdf]] | ||
==Printer Data== | ==Printer Data== | ||
*Downloadable Source data for printer: http://download.lulzbot.com/TAZ/4.0/ | * Downloadable Source data for printer: http://download.lulzbot.com/TAZ/4.0/ | ||
* Additional Octoprint Info https://learn.adafruit.com/octoprint-open-source-host-software/configuring-octoprint-for-lulzbot-taz | |||
==Octoprint Printer Profile Data== | |||
;General | |||
: Name = TAZ Lulzbot 4 | |||
: Identifier = taz_lulzbot_4 | |||
: Model = TAZ Lulzbot 4 | |||
; Printer Bed & Build Volume | |||
: Form Factor = Rectangular | |||
: Origin = Lower Left | |||
: Heated Bed = Check | |||
: Heated Chamber = Un-checked | |||
: Print Volume | |||
:: Bed Width (X) = 300mm | |||
:: Bed Depth (Y) = 300mm | |||
:: Height (Z) = 200mm | |||
: Custom bounding box = Un-checked | |||
; Axes | |||
: Define the maximum speed/feedrate of the individual axes. | |||
: X = 600 mm/min | |||
: Y = 600 mm/min | |||
: Z = 200 mm/min | |||
: E = 300 mm/min | |||
; Hotend & Extruder | |||
: Nozzle Diameter = 0.35 mm | |||
: Number of Extruders = 1 | |||
;Settings from Lulbotz Cura 21.08 | |||
: Name = TAZ Lulzbot 4 | |||
: Identifier = Taz Lulzbot 4 | |||
: Model = TAZ Lulzbot 4 | |||
; Printer Bed & Build Volume | |||
: Build Area Shape = Square | |||
: Origin = Lower Left | |||
: Heated Bed = Check | |||
: Heated Chamber = Un-checked | |||
: Print Volume | |||
:: Bed Width (X) = 290mm | |||
:: Bed Depth (Y) = 275mm | |||
:: Height (Z) = 250mm | |||
: Custom bounding box = Un-checked | |||
; Hotend & Extruder | |||
: Installed Tool Head = Single Extruder V1 | |||
: Nozzle Diameter = 0.35 mm | |||
: Extruder Count = 1 | |||
: GCode Flavor = RepRap (Marlin/Sprinter) | |||
;Start GCode | |||
<nowiki> | |||
;Sliced at: {day} {date} {time} | |||
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |||
;Print time: {print_time} | |||
;Filament used: {filament_amount}m {filament_weight}g | |||
;Filament cost: {filament_cost} | |||
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |||
;M109 S{print_temperature} ;Uncomment to add your own temperature line | |||
G21 ;metric values | |||
G90 ;absolute positioning | |||
M82 ;set extruder to absolute mode | |||
M107 ;start with the fan off | |||
G28 X0 Y0 ;move X/Y to min endstops | |||
G28 Z0 ;move Z to min endstops | |||
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |||
G92 E0 ;zero the extruded length | |||
G1 F200 E3 ;extrude 3mm of feed stock | |||
G92 E0 ;zero the extruded length again | |||
G1 F{travel_speed} | |||
;Put printing message on LCD screen | |||
M117 Printing... | |||
</nowiki> | |||
;End GCode | |||
<nowiki> | |||
;End GCode | |||
M104 S0 ;extruder heater off | |||
M140 S0 ;heated bed heater off (if you have it) | |||
G91 ;relative positioning | |||
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |||
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |||
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |||
M84 ;steppers off | |||
G90 ;absolute positioning | |||
;{profile_string} | |||
</nowiki> | |||
== Firmware == | |||
;Marlin | |||
:http://download.lulzbot.com/TAZ/4.0/software/current/firmware/Marlin/Marlin_TAZ4_1.0.0.1/Marlin/ (Source Code) | |||
:http://download.lulzbot.com/TAZ/4.0/software/current/firmware/Marlin/Marlin_TAZ4_1.0.0.1.hex (Hex Code) | |||
:https://marlinfw.org/ (Marlin Master) | |||
==Replacement Parts== | |||
=== Nozzle Assembly === | |||
* Our printer has a Budaschnozzle 1.1 with 0.35 nozzle | |||
* The Nozzle itself is a 13mm AF hex with an M10 thread. | |||
Replacement Nozzles | |||
===Heater Element=== | |||
The heater element is heated by a 4.7 Ohm Wire Wound Glass Enamelled Resistor. Unfortunately they seem to fail fairly regularly | |||
It is a 6W device. The part is a Vishay or Sfernice RB57 6x22 4R7 Enamelled Resistor. | |||
;Vishay 4.7Ω Wire Wound Resistor 7W ±5% RWM06224R70JA15E1 | |||
:Mfr. Part No. RWM06224R70JA15E1 | |||
:RS Part Number 485-2603 ~£1.40 each | |||
Lulzbot Extruder parts page link | |||
https://shop.lulzbot.com/parts/tool-head-components | |||
Replacement process is documented here https://ohai.lulzbot.com/project/Budaschnozzle_resistor_thermistor/maintenance-repairs/ | |||
[[Category:Equipment]] | |||
[[Category:3D Printing]] |
Latest revision as of 21:51, 19 March 2022
Filament Info
The Lulzbot Taz 4 printer uses 2.85-3.00mm Filament
Octoprint Information
- Octoprint Web Page
- http://hh-octopi-1.local/
- IP Address
- xxx.xxx.xxx.128
- Suggested Tool Flow
-
- Obtain STL or OBJ model from thingiverse or craft one in modelling software.
- Configure print settings and slice using Slic3r.
- Upload directly from Slic3r to Octoprint.
- Start and monitor print from Octoprint web interface.
- Cancel Print if needed or adjust temperatures on the fly.
- Admire freshly 3d printed object.
Manufacturer
- Manufacturer Website: https://www.lulzbot.com/
Compatible Slicer
According to the Lulzbot forums (https://forum.lulzbot.com/t/taz-4-settings/5486/4) the last Cura version Lulzbot had that supported the TAZ4 is 21.08 here http://download.lulzbot.com/Software/Cura/Packages/Cura_21.08/ Configure Cura 21.08 at start up with
- Select Your Machine = Lulzbot TAZ 4 or 5
- Lulzbot TAZ 4-5 Selection = Stock TAZ 4 (PET & v1)
Manual
- Local Copy of Printer Manual:Media:TAZ_Lulbotz_4_Manual.pdf
Printer Data
- Downloadable Source data for printer: http://download.lulzbot.com/TAZ/4.0/
- Additional Octoprint Info https://learn.adafruit.com/octoprint-open-source-host-software/configuring-octoprint-for-lulzbot-taz
Octoprint Printer Profile Data
- General
- Name = TAZ Lulzbot 4
- Identifier = taz_lulzbot_4
- Model = TAZ Lulzbot 4
- Printer Bed & Build Volume
- Form Factor = Rectangular
- Origin = Lower Left
- Heated Bed = Check
- Heated Chamber = Un-checked
- Print Volume
- Bed Width (X) = 300mm
- Bed Depth (Y) = 300mm
- Height (Z) = 200mm
- Custom bounding box = Un-checked
- Axes
- Define the maximum speed/feedrate of the individual axes.
- X = 600 mm/min
- Y = 600 mm/min
- Z = 200 mm/min
- E = 300 mm/min
- Hotend & Extruder
- Nozzle Diameter = 0.35 mm
- Number of Extruders = 1
- Settings from Lulbotz Cura 21.08
- Name = TAZ Lulzbot 4
- Identifier = Taz Lulzbot 4
- Model = TAZ Lulzbot 4
- Printer Bed & Build Volume
- Build Area Shape = Square
- Origin = Lower Left
- Heated Bed = Check
- Heated Chamber = Un-checked
- Print Volume
- Bed Width (X) = 290mm
- Bed Depth (Y) = 275mm
- Height (Z) = 250mm
- Custom bounding box = Un-checked
- Hotend & Extruder
- Installed Tool Head = Single Extruder V1
- Nozzle Diameter = 0.35 mm
- Extruder Count = 1
- GCode Flavor = RepRap (Marlin/Sprinter)
- Start GCode
;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M109 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M82 ;set extruder to absolute mode M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm G92 E0 ;zero the extruded length G1 F200 E3 ;extrude 3mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing...
- End GCode
;End GCode M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string}
Firmware
- Marlin
- http://download.lulzbot.com/TAZ/4.0/software/current/firmware/Marlin/Marlin_TAZ4_1.0.0.1/Marlin/ (Source Code)
- http://download.lulzbot.com/TAZ/4.0/software/current/firmware/Marlin/Marlin_TAZ4_1.0.0.1.hex (Hex Code)
- https://marlinfw.org/ (Marlin Master)
Replacement Parts
Nozzle Assembly
- Our printer has a Budaschnozzle 1.1 with 0.35 nozzle
- The Nozzle itself is a 13mm AF hex with an M10 thread.
Replacement Nozzles
Heater Element
The heater element is heated by a 4.7 Ohm Wire Wound Glass Enamelled Resistor. Unfortunately they seem to fail fairly regularly
It is a 6W device. The part is a Vishay or Sfernice RB57 6x22 4R7 Enamelled Resistor.
- Vishay 4.7Ω Wire Wound Resistor 7W ±5% RWM06224R70JA15E1
- Mfr. Part No. RWM06224R70JA15E1
- RS Part Number 485-2603 ~£1.40 each
Lulzbot Extruder parts page link https://shop.lulzbot.com/parts/tool-head-components
Replacement process is documented here https://ohai.lulzbot.com/project/Budaschnozzle_resistor_thermistor/maintenance-repairs/